Tuesday, September 29, 2026

Scavenging

    My parents were Great Depression era children, and they had more kids than they could afford; three more. Thus, my four sisters and I grew up, let’s just say, in a VERY frugal household. We wore hand-me-down clothes from neighbors and the church. Meals were simple and limited; no seconds.

 

As a result, we all learned how to get what we needed without criminal activity, for the most part, but also without jobs. I collected soda and beer bottles and cashed them in at two cents a bottle. A wagonload would get me 40-60 cents in a good week. I also cut grass, raked leaves, and shoveled snow, lots of snow, for a dollar per house. Cash, and all mine.

 

Once I could drive, stuff set out by the road or curb became my preferred source but dumpsters behind businesses and roll-off dumpsters at construction sites also served me well. The law says that anything thrown out is no longer the property of the former owner, but businesses could, and did, place safety restrictions on going into the dumpster. So, I used a long tool handle I found and attached a metal hook to the end, and I could get most things out that I had an interest in obtaining.

 

Military bases are gold mines with units stashing excess supplies out in the woods far from the cantonment areas. Then the Supply Sergeant forgot about them. I found many supply dumps over the years full of parts, equipment, tools, etc. I went out into training areas and picked up brass from exercises; blanks that couldn’t be turned in as dross. As I walked around, I found dropped equipment such as sleeping bags, poncho liners, helmets, knives, munitions, magazines, etc. With Soldiers moving every couple of years there was always a steady supply of stuff at the curb in the housing areas. I have a storage shed at my house filled with lawnmowers, shopvacs, shovels, rakes, spare tires, car batteries, tools, etc. I have given all my brothers-in-law lawnmowers and shopvacs. All my boys have a complete set of yard tools; shovels, rakes, axes, sledgehammers, picks, prybars, hedge clippers, etc.

 

In my garage is a parts bin rack filled with bolts, nuts, washers, nails, screws of all types, wire connectors, bushings; all sorted and labeled. I have a tandem kayak that I found in the woodline behind a house, stacks of bricks and pavers, tubs of construction sand and salt; all left behind by construction and maintenance crews. On my kayak fishing trips on rivers I scan the shoreline and have recovered gas cans, a complete tent in its carry bag, a brand new rain suit (this past weekend), paddles, PFDs, two fishing rods, boat bumpers, an anchor, etc.

 

Everything was free. Everything was prevented from going into a landfill. Everything out of the rivers helped clean them up.

Sunday, January 18, 2026

Kubota B2660 Snow Blower Shear Pin repair

    One of the many annoyances of rural life is shear pins. They are essential to protect valuable, irreplaceable equipment. They are made to break if a load is applied to a drive shaft. We are thankful that they do shear and the equipment is safe. But it never seems like you have a replacement on hand when one breaks. Trip over to Tractor Supply.

 

    You cannot just use any bolt that fits, you must use a bolt designed to break. Shear pin bolts are category 2 or 5 bolts. These are hardened, which makes them brittle. That brittleness makes them break if an unusually strong load is applied, such as when a moving part gets jammed. In my case, I was clearing snow from my neighbor's parking lot and I scooped up a trailer pintle pin, which jammed the blower fan.

 

    The shear pin sheared, like it is supposed to and the snow blower wasn't damaged.

 

 
    I went online and downloaded the User Manual and then looked for the parts diagram. It showed a shear pin, Part-20, pretty much where I figured it would be. 
 
 

    I was hoping this shear pin would be accessible, and it is. There is a closed gearbox on the outside and I was afraid it would be in there. I used a torpedo kerosene heater to melt the snow and ice off the snow blower so I could see all the parts and have access to this pin location. I have it rotated 90 degrees just to see and measure the bolt size; it is a 1/4 inch bolt. The bolt hole goes through part shown and also the lower part of the orange part, hidden behind the shaft. 

 


    Very hard place to get my big hands into. I could only turn the wrench one eighth of a turn at a time so it took a while. But, it is now all fixed up and ready to go without hauling it to a shop and paying hundreds of dollars.